Publication

2024

A.K. Boukellal; M. Sarebanzadeh; A. Orozco-Caballero; F. Sket; J. LLorca; D. Tourret - Grain growth competition and formation of grain boundaries during solidification of hcp alloys. acta materialia 269, 2024. DOI: DOI10.1016/j.actamat.2024.119830

2023

J.C. Nieto-Fuentes, J. Espinoza, F. Sket, J.A. Rodríguez-Martínez - High-velocity impact fragmentation of additively-manufactured metallic tubes. journal of the mechanics and physics of solids 174, 105248-105248, 2023. DOI: 10.1016/j.jmps.2023.105248
S. Bafaluy Ojea; J. Torrents-Barrena. J. Torrents-Barrena, MT. Pérez-Prado, R. Muñoz Moreno; Sket. F - Binder jet green parts microstructure: advanced quantitative analysis. journal of materials research and technology 23, 3974-3986, 2023. DOI: DOI10.1016/j.jmrt.2023.02.051

2022

Pandey, Akshya K.; Alvaredo, Paula; Milenkovic, Srdjan; Sket, Federico - Development of powders of Ti-Fe-Sn ultrafine eutectics for laser additive manufacturing. powder technology 404, 117416-117416, 2022. DOI: 10.1016/j.powtec.2022.117416
Raúl Muñoz, Rocío Seltzer, Federico Sket, Carlos González, Javier Llorca - Influence of hybridisation on energy absorption of 3D woven composites under low-velocity impact loading. Modelling and experimental validation. international journal of impact engineering 165, 104229-104229, 2022. DOI: 10.1016/j.ijimpeng.2022.104229
Lizarralde, I; Sapountzi, E.; Benethuiliere, T.; Sket, F.; Gonzalez, C. - An X-ray computed tomography analysis of damage induced by thermal cycling in non-crimp fabric composites. composites part a-applied science and manufacturing 152, 106699-106699, 2022. DOI: 10.1016/j.compositesa.2021.106699

2021

Castro, J.; Sket, F.; Helfen, L.; Gonzalez, C. - In situ local imaging and analysis of impregnation during liquid moulding of composite materials using synchrotron radiation computed laminography. composites science and technology 215, 108999-108999, 2021. DOI: 10.1016/j.compscitech.2021.108999
Marvi-Mashhadi, M.; Vaz-Romero, A.; Sket, F.; Rodriguez-Martinez, J. A. - Finite element analysis to determine the role of porosity in dynamic localization and fragmentation: Application to porous microstructures obtained from additively manufactured materials. international journal of plasticity 143, 102999, 2021. DOI: 10.1016/j.ijplas.2021.102999
Tsipas, S. A.; Tabares, E.; Weissgaerber, T; Hutsch, T.; Sket, F.; Velasco, B. - Thermophysical properties of porous Ti2AlC and Ti3SiC2 produced by powder metallurgy. journal of alloys and compounds 857, 158145, 2021. DOI: 10.1016/j.jallcom.2020.158145

2020

Gussone, J.; Bugelniga, K.; Barriobero-Vila, P.; da Silva, J.C.; Hecht, U.; Dresbach, Ch.; Sket, F.; Cloetens, P.; Stark, A.; Schell, N.; Haubrich, J.; Requena, G. - Ultrafine eutectic Ti-Fe-based alloys processed by additive manufacturing – A new candidate for high temperature applications. applied materials today 20, 100767, 2020. DOI: 10.1016/j.apmt.2020.100767
Castro, J; Sket, F; González, C. - S-XCT experimental determination of local contact angle and meniscus shape in liquid moulding of composites. 199, 108362, 2020. DOI: 10.1016/j.compscitech.2020.108362
Requena, G.; Bugelnig, K.; Sket, F.; Milenkovic, S.; Roedler, G.; Weisheit,A.; Gussone, J.; Haubrich, J.; Barriobero-Vila, P.; Pusztai, T.; Gránásy, L.; Theofilatos, A.; Da Silva, J.C.; Hechte, U. - Ultrafine Fe-Fe2Ti eutectics by directed energy deposition: Insights into microstructure formation based on experimental techniques and phase field modelling. additive manufacturing 33, 2020. DOI: 10.1016

2019

Riezzo, MA; Simmons, M; Russell, B; Sket, F; Martinez, V; Gonzalez, C - Dynamic characterisation of interlaminar fracture toughness in carbon fibre epoxy composite laminates. composites part a-applied science and manufacturing 126, 2019. DOI: 10.1016/j.compositesa.2019.105597
Pushkareva, M; Sket, F; Segurado, J; Llorca, J; Yandouzi, M; Weck, A - Effect of grain orientation and local strains on void growth and coalescence in titanium. materials science and engineering a-structural materials properties microstructure and processing 760, 258-266, 2019. DOI: 10.1016/j.msea.2019.06.004
Torres, J. J.; Simmons, M.; Sket, F.; Gonzalez, C. - An analysis of void formation mechanisms in out-of-autoclave prepregs by means of X-ray computed tomography. composites part a-applied science and manufacturing 117, 230-242, 2019. DOI: 10.1016/j.compositesa.2018.11.010

2018

Bugelnig, Katrin; Germann, Holger; Steffens, Thomas; Sket, Federico; Adrien, Jerome; Maire, Eric; Boller, Elodie; Requena, Guillermo - Revealing the Effect of Local Connectivity of Rigid Phases during Deformation at High Temperature of Cast AlSi12Cu4Ni(2,3)Mg Alloys. materials 11, 2018. DOI: 10.3390/ma11081300
Senokos, Evgeny; Ou, Yunfu; Jose Torres, Juan; Sket, Federico; Gonzalez, Carlos; Marcilla, Rebeca; Vilatela, Juan J. - Energy storage in structural composites by introducing CNT fiber/polymer electrolyte interleaves. scientific reports 8, 2018. DOI: 10.1038/s41598-018-21829-5
Bugelnig, Katrin; Sket, Federico; Germann, Holger; Steffens, Thomas; Koos, Robert; Wilde, Fabian; Boller, Elodie; Requena, Guillermo - Influence of 3D connectivity of rigid phases on damage evolution during tensile deformation of an AlSi12Cu4Ni2 piston alloy. materials science and engineering a-structural materials properties microstructure and processing 709, 193-202, 2018. DOI: 10.1016/j.msea.2017.10.035

2017

Gutierrez, R. Fernandez; Sket, F.; Maire, E.; Wilde, F.; Boller, E.; Requena, G. - Effect of solution heat treatment on microstructure and damage accumulation in cast Al-Cu alloys. journal of alloys and compounds 697, 341-352, 2017. DOI: 10.1016/j.jallcom.2016.11.280
O. Falco, C. S. Lopes, F. Naya, F. Sket, P. Maimi, and J. A. Mayugo - Modelling and simulation of tow-drop effects arising from the manufacturing of steered-fibre composites. composites part a-applied science and manufacturing 93, 59-71, 2017. DOI: 10.1016/j.compositesa.2016.11.015

2016

Sket, F.; Enfedaque, A.; Diaz Lopez, C.; Gonzalez, C.; Molina-Aldareguia, J.; LLorca, J. - X-ray computed tomography analysis of damage evolution in open hole carbon fiber-reinforced laminates subjected to in-plane shear. composites science and technology 133, 40-50, 2016. DOI: 10.1016/j.compscitech.2016.06.012
Moya, Jose S.; Martinez, Arturo; Lopez-Piriz, Roberto; Guitian, Francisco; Diaz, Luis A.; Esteban-Tejeda, Leticia; Cabal, Belen; Sket, Federico; Fernandez-Garcia, Elisa; Tomsia, Antoni P.; Torrecillas, Ramon - Histological response of soda-lime glass-ceramic bactericidal rods implanted in the jaws of beagle dogs. scientific reports 6, 2016. DOI: 10.1038/srep31478
Canelo-Yubero, David; Requena, Guillermo; Sket, Federico; Poletti, Cecilia; Warchomicka, Fernando; Daniels, John; Schell, Norbert; Stark, Andreas - Load partition and microstructural evolution during in situ hot deformation of Ti-6Al-6V-2Sn alloys. materials science and engineering a-structural materials properties microstructure and processing 657, 244-258, 2016. DOI: 10.1016/j.msea.2016.01.059

2015

Sket, Federico; Fernandez, Ana; Jerusalem, Antoine; Molina-Aldareguia, Jon M.; Teresa Perez-Prado, Maria - Effect of Hydrostatic Pressure on the 3D Porosity Distribution and Mechanical Behavior of a High Pressure Die Cast Mg AZ91 Alloy. metallurgical and materials transactions a-physical metallurgy and materials science 46A, 4056-4069, 2015. DOI: 10.1007/s11661-015-3024-z
Asghar, Z.; Requena, G.; Sket, F. - Multiscale tomographic analysis of heterogeneous cast Al-Si-X alloys. journal of microscopy 259, 1-9, 2015. DOI: 10.1111/jmi.12241
Sket, F.; Rodriguez-Hortala, M.; Molina-Aldareguia, J. M.; Llorca, J.; Maire, E.; Requena, G. - In situ tomographic investigation of damage development in +/- 45 degrees carbon fibre reinforced laminates. materials science and technology 31, 587-593, 2015. DOI: 10.1179/1743284714Y.0000000561
Vila, Joaquim; Sket, Federico; Wilde, Fabian; Requena, Guillermo; Gonzalez, Carlos; LLorca, Javier - An in situ investigation of microscopic infusion and void transport during vacuum-assisted infiltration by means of X-ray computed tomography. composites science and technology 119, 12-19, 2015. DOI: 10.1016/j.compscitech.2015.09.016
Wu, L.; Sket, F.; Molina-Aldareguia, J. M.; Makradi, A.; Adam, L.; Doghri, I.; Noels, L. - A study of composite laminates failure using an anisotropic gradient-enhanced damage mean-field homogenization model. composite structures 126, 246-264, 2015. DOI: 10.1016/j.compstruct.2015.02.070
Vigueras, Guillermo; Sket, Federico; Samaniego, Cristobal; Wu, Ling; Noels, Ludovic; Tjahjanto, Denny; Casoni, Eva; Houzeaux, Guillaume; Makradi, Ahmed; Molina-Aldareguia, Jon M.; Vazquez, Mariano; Jerusalem, Antoine - An XFEM/CZM implementation for massively parallel simulations of composites fracture. composite structures 125, 542-557, 2015. DOI: 10.1016/j.compstruct.2015.01.053

2014

Renversade, Loic; Ruoff, Herbert; Maile, Karl; Sket, Federico; Borbely, Andras - Microtomographic assessment of damage in P91 and E911 steels after long-term creep. international journal of materials research 105, 621-627, 2014. DOI: 10.3139/146.111056
Munoz, R.; Martinez, V.; Sket, F.; Gonzalez, C.; LLorca, J. - Mechanical behavior and failure micromechanisms of hybrid 3D woven composites in tension. composites part a-applied science and manufacturing 59, 93-104, 2014. DOI: 10.1016/j.compositesa.2014.01.003
Sket, F.; Enfedaque, A.; Alton, C.; Gonzalez, C.; Molina-Aldareguia, J. M.; Llorca, J. - Automatic quantification of matrix cracking and fiber rotation by X-ray computed tomography in shear-deformed carbon fiber-reinforced laminates. composites science and technology 90, 129-138, 2014. DOI: 10.1016/j.compscitech.2013.10.022

2013

Biswas, Somjeet; Sket, Federico; Chiumenti, Michele; Gutierrez-Urrutia, Ivan; Molina-Aldareguia, Jon M.; Teresa Perez-Prado, Maria - Relationship Between the 3D Porosity and beta-Phase Distributions and the Mechanical Properties of a High Pressure Die Cast AZ91 Mg Alloy. metallurgical and materials transactions a-physical metallurgy and materials science 44A, 4391-4403, 2013. DOI: 10.1007/s11661-013-1783-y
Hernandez, S.; Sket, F.; Gonzalez, C.; LLorca, J. - Optimization of curing cycle in carbon fiber-reinforced laminates: Void distribution and mechanical properties. composites science and technology 85, 73-82, 2013. DOI: 10.1016/j.compscitech.2013.06.005

2012

Sket, F.; Seltzer, R.; Molina-Aldareguia, J. M.; Gonzalez, C.; LLorca, J. - Determination of damage micromechanisms and fracture resistance of glass fiber/epoxy cross-ply laminate by means of X-ray computed microtomography. composites science and technology 72, 350-359, 2012. DOI: 10.1016/j.compscitech.2011.11.025

2011

Borbely, Andras; Dzieciol, Krzysztof; Sket, Federico; Isaac, Augusta; di Michiel, Marco; Buslaps, Thomas; Kaysser-Pyzalla, Anke R. - Characterization of creep and creep damage by in-situ microtomography. jom 63, 78-84, 2011. DOI: 10.1007/s11837-011-0117-z
Dzieciol, K.; Borbely, A.; Sket, F.; Isaac, A.; Di Michiel, M.; Cloetens, P.; Buslaps, Th; Pyzalla, A. R. - Void growth in copper during high-temperature power-law creep. acta materialia 59, 671-677, 2011. DOI: 10.1016/j.actamat.2010.10.003
Hernandez, S.; Sket, F.; Molina-Aldareguia, J. M.; Gonzalez, C.; LLorca, J. - Effect of curing cycle on void distribution and interlaminar shear strength in polymer-matrix composites. composites science and technology 71, 1331-1341, 2011. DOI: 10.1016/j.compscitech.2011.05.002
LLorca, J.; Gonzalez, C.; Molina-Aldareguia, J. M.; Segurado, J.; Seltzer, R.; Sket, F.; Rodriguez, M.; Sadaba, S.; Munoz, R.; Canal, L. P. - Multiscale Modeling of Composite Materials: a Roadmap Towards Virtual Testing. advanced materials 23, 5130-5147, 2011. DOI: 10.1002/adma.201101683

2010

Sket, F.; Dzieciol, K.; Borbely, A.; Kaysser-Pyzalla, A. R.; Maile, K.; Scheck, R. - Microtomographic investigation of damage in E911 steel after long term creep. materials science and engineering a-structural materials properties microstructure and processing 528, 103-111, 2010. DOI: 10.1016/j.msea.2010.07.029

Caballero, JI, Cosarinsky, G, Camacho, J, Menasalvas, E, Gonzalo-Martin, C, Sket, F - A Methodology to Automatically Segment 3D Ultrasonic Data Using X-ray Computed Tomography and a Convolutional Neural Network. applied sciences-basel 13, . DOI: DOI10.3390/app13105933