Activities

ABSTRACT The previous design of engines used for commercial aircrafts fan and turbine were driven with same shaft; new geared engines decouple fan and the low pressure turbine increasing angular velocity, and also centrifugal forces, so a change from conventional superalloy blades to lighter

Abstract Additive manufacturing (AM) is a layer by layer process that has the potential to disrupt traditional fabrication methods. It allows fast manufacturing of three dimensional pieces from metallic powders, with great exibility of design, potential for weight reduction, fast production speed for

The PhD Defense will take place,  at 12 noon, on next Friday (26th of October) in the “sala verde”, on the first floor, in the Escuela de Ingenieros de Caminos, UPM (ETSI Caminos, Ciudad Universitaria)  The dissertation is entitled “Energy Harvesting

 Abstract:  It is presented a rigorous framework developed for formulation of constitutive models. Based on representation theory for tensor functions and scale-bridging theorems, this framework enables the development of constitutive models that account for the influence of crystallographic structures and

We are hosting the 55th edition of the Annual Technical Meeting of the Society of Engineering Science (SES). The SES Technical Meeting is held annually to provide an interdisciplinary forum for the exchange of ideas and information among the various

Abstract Over the past few years, graphitic carbon nitride (g-CN) has attracted widespread attention due to its outstanding electronic properties, which have been exploited in various applications, including in photo- and electro-catalysis, heterogeneous catalysis, CO2 reduction, water splitting, light-emitting diodes, and solar cells.

Discrete slip crystal plasticity modeling of deformation in nanolayered materials Irene J. Beyerlein1, Tianju Chen2, Rui Yuan2, Caizhi Zhou2,3 1 Mechanical Engineering Department, Materials Department, University of California at Santa Barbara, Santa Barbara 93106, USA 2 Department of Materials Science

Abstract Herein, highly ordered mesoporous pseudocapacitive electrodes for superior Li-ion storage are discussed. Hierarchical 1-D Co3O4nanorods of size ~20 nm with interfaces between the crystallites were synthesized using hydrothermal method followed by calcination. This 1D nanorods exhibited pseudocapacitive behavior with

Abstract Additive manufacturing (AM) is a layer by layer process that has the potential to disrupt traditional fabrication methods. It allows fast manufacturing of three dimensional pieces from metallic powders, with great exibility of design, potential for weight reduction, fast production speed for

Researchers belonging to all IMDEA institutes solved a new crime in the activity “IMDEA-CSI” as part of the European Researchers’ Night Madrid 2018. More information about the event in this podcast (radio show “Por tres razones”, RTVE)

Abstract: Solidification is one of the major steps in producing parts from the molten material in casting, welding or additive manufacturing. On top of process optimization and simulation to obtain good mould filling and minimized defects, the quality of the

Abstract In this study, dimension control and nanostructure design were applied in developing electrode materials for superior Na-ion storage. Firstly, hierarchical Co3O4nanorods with increased number of interfaces between individual nanocrystallites were prepared for enhancing pseudocapacitance assisted Na-ions storage. When evaluated

ABSTRACT: The main objective of this work is to create a physical platform for material characterization and parameter identification at macroscale as a function of applied strain rate, understanding how the strain rate affects the damage and mechanical response of

The PhD Defense will take place,  at 12 noon, on next Friday (7th of September) in the “sala verde”, on the first floor, in the Escuela de Ingenieros de Caminos, UPM (ETSI Caminos, Ciudad Universitaria)  The dissertation is entitled “Development of

Abstract: Advanced composite materials are now used in a wide range of industries, including aerospace, marine, construction, transport and recreational sport. The ever-increasing pressure on producing quality parts effectively and efficiently has led to many innovations over the years in

Research Assistant Elisa Fresta has been awarded a Prize for one of the best Master Thesis (year 2015/2016) from the University of Turin. The thesis was developed at both the University of Turin and the University of Erlangen-Nuremberg under the supervision of Prof. Claudia Barolo

Researchers from our institute have developed in collaboration with IMDEA Energy a new current collector-free  capacitive deionization architecture based on electrodes consisting of a porous metal oxide network interpenetrated into porous fibres of carbon nanotube. The full device has a large salt adsorption

Abstract: In view of the future application of polymer matrix composites for structural components subjected to impact loads, there is a need for development of experimentally calibrated constitutive models for polymers that include their inherent viscoelastic and viscoplastic behavior. These