Activities

Our Institute has started a new research line on novel bioresorbable materials for implant applications (see related news in Spanish). This work will be initially supported by the BIOIMPLANT project (funded by the European Union under the Marie Skłodowska-Curie Actions Innovative Training Networks).

The PhD Defense will take place,  at 11:30 am, on next Thursday (22nd of November) in ETSI Industriales in aula D.  The dissertation is entitled “Numerical Methods for the simulation of high velocity impact” Here is the link of the

Abstract: This study aims to increase the understanding of the tensile failure of unidirectional hybrid and non-hybrid composite when subjected to tensile loadings. To achieve this goal several models with increasing complexity have been developed and implemented and the effects

 ABSTRACT  Carbon nanotubes (CNTs) have been a focus of nanomaterial research over the past two decades, due to their wide range of potential applications. In recent years, studies have shown a high degree of molecular control of CNTs in terms

Abstract Additive manufacturing (AM) is a layer by layer process that has the potential to disrupt traditional fabrication methods. It allows fast manufacturing of three dimensional pieces from metallic powders, with great exibility of design, potential for weight reduction, fast

Rubén Costa explains his research line related to biological lightning in the national tv news (in Spanish only)

Abstract: Ni-based superalloys play an extremely important role in the aerospace industry due to their outstanding strength and chemical stability at high temperature. Most demanded components employed in jet engines are manufactured with these novel materials. Several statistical studies confirm

ABSTRACT The previous design of engines used for commercial aircrafts fan and turbine were driven with same shaft; new geared engines decouple fan and the low pressure turbine increasing angular velocity, and also centrifugal forces, so a change from conventional superalloy blades to lighter

Abstract Additive manufacturing (AM) is a layer by layer process that has the potential to disrupt traditional fabrication methods. It allows fast manufacturing of three dimensional pieces from metallic powders, with great exibility of design, potential for weight reduction, fast production speed for

The PhD Defense will take place,  at 12 noon, on next Friday (26th of October) in the “sala verde”, on the first floor, in the Escuela de Ingenieros de Caminos, UPM (ETSI Caminos, Ciudad Universitaria)  The dissertation is entitled “Energy Harvesting

 Abstract:  It is presented a rigorous framework developed for formulation of constitutive models. Based on representation theory for tensor functions and scale-bridging theorems, this framework enables the development of constitutive models that account for the influence of crystallographic structures and

We are hosting the 55th edition of the Annual Technical Meeting of the Society of Engineering Science (SES). The SES Technical Meeting is held annually to provide an interdisciplinary forum for the exchange of ideas and information among the various

Abstract Over the past few years, graphitic carbon nitride (g-CN) has attracted widespread attention due to its outstanding electronic properties, which have been exploited in various applications, including in photo- and electro-catalysis, heterogeneous catalysis, CO2 reduction, water splitting, light-emitting diodes, and solar cells.

Discrete slip crystal plasticity modeling of deformation in nanolayered materials Irene J. Beyerlein1, Tianju Chen2, Rui Yuan2, Caizhi Zhou2,3 1 Mechanical Engineering Department, Materials Department, University of California at Santa Barbara, Santa Barbara 93106, USA 2 Department of Materials Science

Abstract Herein, highly ordered mesoporous pseudocapacitive electrodes for superior Li-ion storage are discussed. Hierarchical 1-D Co3O4nanorods of size ~20 nm with interfaces between the crystallites were synthesized using hydrothermal method followed by calcination. This 1D nanorods exhibited pseudocapacitive behavior with

Abstract Additive manufacturing (AM) is a layer by layer process that has the potential to disrupt traditional fabrication methods. It allows fast manufacturing of three dimensional pieces from metallic powders, with great exibility of design, potential for weight reduction, fast production speed for

Researchers belonging to all IMDEA institutes solved a new crime in the activity “IMDEA-CSI” as part of the European Researchers’ Night Madrid 2018. More information about the event in this podcast (radio show “Por tres razones”, RTVE)

Abstract: Solidification is one of the major steps in producing parts from the molten material in casting, welding or additive manufacturing. On top of process optimization and simulation to obtain good mould filling and minimized defects, the quality of the